Nous ne livrons malheureusement pas dans ce pays.

SERVICE CHAT TALK TO THE PEOPLE THAT BUILD YOUR BIKE:

CHAT IS NOT AVAILABLE RIGHT NOW. WE WILL BE BACK ONLINE SOON.

Notre Servicecenter est disponible aujourd'hui des 9.00 h. Vous pouvez nous joindre au 0890 710 132 ou nous envoyer un e-mail.
Difficulté: Moyen
Dans cette catégorie vous trouverez des ateliers dignes du plus grand intérêt pour un mécanicien maniaque passionné. Il vous faudra un certain niveau de compétence technique ainsi qu'une expérience acquise dans l'entretien et la maintenance de cycles. Vous aurez besoin d'outils spéciaux, qui ne sont normalement pas disponibles dans les caisses à outils standard.
Outils: Sujets similaires: Impression de l'article

Renthal Stems Installation Instructions

Renthal Duo installation instructions

Preparations


The fork shaft must be clean, dry and free of burr before starting the installation work.

Install the stem

1. Remove the Ahead cover and the spacer from the fork shaft using the 5 mm Allen key. Picture 1 Picture 2 Picture 3

Important:
Do not undo the screw connection of the bottom half of the stem which is already installed. Otherwise you will have to reset the steering head bearing play. The stem and the steering head bearing has already been set correctly by us.

2. Apply a little grease to the thread and under the screw heads.
3. Position the handlebar in the stem. Align the handlebar so that it is precisely in the centre. Picture 4
4. Place the top half of the stem on the fork shaft and handlebar. Picture 5
5. Now check that the handlebar is correctly positioned and aligned in the stem.
6. Place the two screws from below into the stem and tighten them alternately and crossways to a torque of 5 Nm. Picture 6
7. Place the two screws from above into the stem and tighten them alternately and crossways to a torque of 5 Nm. Picture 7
8. Ensure that the clamping is uniform.
9. Secure the top half to the fork shaft using the silver screw using a torque of 5 Nm. Picture 8
10. Place the spacer on the stem and fork shaft. Picture 9
11. Tightening the securing screw on the Ahead cover with a torque of 4 Nm. Picture 10

Care/Maintenance

  • Check that all the bolts are tightened with the correct torque before every ride.
  • Check all the parts at regular intervals for signs of damage, particularly after accidents and falls.
  • Clean all the screws and parts after fitted or removing the stem or handlebar and regrease the screws.


Renthal Integra installation instructions

Prepare the fork crowns

1. Clean the thread and the adjusting surfaces at the top of the fork bridge.

Install the stem

2. Apply a little grease to the thread and under the screw heads.
Position the handlebar in the stem. Align the handlebar so that it is precisely in the centre.
3. Insert the 6x25 mm screws into the rear installation holes either through the 45 mm or the 50 mm installation boreholes.
4. Insert the M6x35 mm screws into the corresponding front installation boreholes
5. Insert the screws into the fork crown mounting at the front.
6. Tighten the screws on the fork crown by hand initially.
7. Tighten the screws on the fork crown alternately crossways with a torque of 10 Nm.
8. Insert the M5x16mm screws into the handlebar mounting and align the handlebar.
9. Tighten the screws on the handlebar mounting alternately and crossway with a torque of 6 Nm.

Care/Maintenance

  • Check that all the bolts are tightened with the correct torque before every ride.
  • Check all the parts at regular intervals for signs of damage, particularly after accidents and falls.
  • Clean all the screws and parts after fitted or removing the stem or handlebar and regrease the screws.

Canyon s'efforce constamment d'assurer la qualité et l'exactitude des informations contenues dans ce support technique. Les réparations ou réglages que vous effectuez sur votre vélo sont sous votre entière responsabilité. Si vous avez le moindre doute sur ce qu'il faut faire, envoyez votre vélo chez Canyon directement ou chez un vélociste qualifié. Canyon ne donne aucune garantie ou n'accepte aucune responsabilité quant aux informations contenues dans ce support technique.


Picture 1:Undo the screw on top of the ahead stem cap

Picture 1:Undo the screw on top of the ahead stem cap

Picture 2:Remove the cap

Picture 2:Remove the cap

Picture 3: Remove the Spacer

Picture 3: Remove the Spacer

Picture 4: Fit the handlebar

Picture 4: Fit the handlebar

Picture 5: Place the top half of the stem on the fork shaft and handlebar

Picture 5: Place the top half of the stem on the fork shaft and handlebar

Picture 7: Tighten the two screws at the bottom with the correct torque

Picture 7: Tighten the two screws at the bottom with the correct torque

Picture 6: Tighten the front screws with the correct torque

Picture 6: Tighten the front screws with the correct torque

Picture 8: Tighten the screw at the back withthe correct torque

Picture 8: Tighten the screw at the back withthe correct torque

Picture 9: Mount the spacer

Picture 9: Mount the spacer

Picture 10:Tighten the scew of the ahead cap with the correct torque

Picture 10:Tighten the scew of the ahead cap with the correct torque

Cet article vous a-t-il aidé ?OuiNon

Pure Cycling.