Unfortunately, we do not ship to your country.

Se till vilka länder vi sänder

Kontakta vårt servicenummer. Vi har öppet vardagar till 15:00: 0767 - 650 596

Svårighetsgrad: lätt
Dessa arbeten är enkla för den som är intresserad av cykling. För den här workshopen krävs inga speciella verktyg utan det räcker med standardverktyg som insexnycklar, tänger eller skruvmejslar. Här hittar du all information om hur du justerar din cykel.

Verktyg: Downloads: Liknande ämnen: Skriv ut artikel

Assemble Roadbike from BikeGuard

Artikeln på svenska

It is simple to assemble your Canyon bicycle. If you follow the instructions below, your bike will be ready to go within a couple of minutes.

1. Cut through the adhesive tape very carefully using a sharp knife or a pair of scissors. Be careful not to damage the BikeGuard.

2. Now you can pull the straps out of the slits and open the BikeGuard.

3. With every Canyon bicycle you receive a torque wrench. This wrench is placed on top of the pillar in the middle of the BikeGuard box. Take the wrench out of the box and keep it in a safe place. Now you can remove the seat pillar from the box.

4. In the rear part of the box you can find the seatpost fitted to the saddle. Take both items out of the BikeGuard. Picture 1

5. Now you can remove the front wheel from the box. Picture 2

6. Remove the rear wheel now. It is easier to remove if you push the sides of the BikeGuard apart. Please take extra care not to scratch the bike frame while you are taking the rear wheel out of the box.

7. Remove the frame from the box.

8. Position the bike in such a way that the fork is hanging out of the BikeGuard as shown. Picture 3

9. Remove the foil from the handlebar. Please be very careful not to damage the cables attached to the handlebar.

10. Remove the front plate using a standard wrench, not a torque wrench.

11. Assemble the handlebar to the stem. Place the bar symmetrically to the stem. You need to tighten the screws with the correct torque. The correct torque is printed on the stem. Picture 4 Tighten the screws using a torque wrench. Picture 5 Tighten each screw crosswise. Tighten each screw three times.

The slits between stem and front plate should have the same distance, both on top and on the bottom of the front plate.

12. Pull the plastic caps from the axles of both wheels. Picture 6

13. Now you can assemble the quick releases to the front wheel. The springs need to be placed correctly on the rods. Picture 7

14. Assemble the front wheel now. The wheel needs to be placed in the very centre of the dropouts. Picture 8 First turn the fixing screw and then you close the quick release lever. This lever should point backwards.
15. Now remove the foil from the chain stay. Use a pair of scissors and take extra care not to scratch the frame while cutting the foil.

16. Remove the small wooden slat. Picture 9 Mount the quick release to the rear wheel axle. Picture 10

17. Assemble the rear wheel now. Pull the cage of the rear derailleur backwards. The chain should be placed on the smallest sprocket. Picture 11

18. Close the brake releases on both brakes.

19. You can now fit the seatpost. Lighly lubricate the seatpost if both seatpost and frame are aluminium, except for dropper seatposts such as the Rock Shox Reverb. CAUTION: for Rock Shox Reverb seatposts you must only ever use friction paste and never grease. Apply a little friction paste to the inside of the seat tube and to the relevant surface of the seatpost.

CAUTION: only ever use carbon assembly paste and never grease if the seatpost, the frame, or both, are carbon. Apply a little carbon assembly paste to the inside of the seat tube and to the relevant surface of the seatpost.

CAUTION: always insert the seatpost into the frame at least as far as its minimum insertion length. The seatpost is marked accordingly to help you with this.


20. Assemble the pedals (not included). Apply grease to the thread. Use a 15mm jaw wrench, a pedal wrench or an Allen key to tighten the pedal. Picture 13 Attention: Mind the rotation direction of the threads when mounting the pedals.

21. Check the air pressure in both tyres. The suggested pressure is printed on the sides of the tyres. Pump up the tyre if necessary.

Only for french customers





Ensure that all screws and bolts are tightened to the correct torque. The correct torque is indicated on the component itself, in the bike manual provided with your new bike, or here in the Technical Support Center.


Canyon jobbar hårt för att informationen här i teknisk support ska vara så korrekt och uppdaterad som möjligt. Dock sker alla reparationer som du gör själv på egen risk. Skulle du vara tveksam över något så ska du skicka in cykeln till oss eller en kvalificerad mekaniker/cykelverkstad. Canyon tar inget ansvar och ger ingen garanti på att informationen här i teknisk support är korrekt.


Pictue 1: Pull out the saddle

Pictue 1: Pull out the saddle

Picture 2: Squeeze the BikeGuard a bit when you remove the wheels

Picture 2: Squeeze the BikeGuard a bit when you remove the wheels

Picture 3: Position the bike as shown for assembly

Picture 3: Position the bike as shown for assembly

Picture 4: The correct torque is printed on the stem

Picture 4: The correct torque is printed on the stem

Picture 5: Tighten the screws crosswise with the correct torque

Picture 5: Tighten the screws crosswise with the correct torque

Picture 6: Remove the caps from the axles

Picture 6: Remove the caps from the axles

Picture 7: Take care that the springs face in the correct direction

Picture 7: Take care that the springs face in the correct direction

Picture 8: Take care that the wheels are properly fitted

Picture 8: Take care that the wheels are properly fitted

Picture 9: Remove the wooden slat

Picture 9: Remove the wooden slat

Picture 10: Rear quick release

Picture 10: Rear quick release

Picture 11: Pull the rear derailleur backwards to mount the rear wheel

Picture 11: Pull the rear derailleur backwards to mount the rear wheel

Picture 12: Do not pull out the seatpost too far

Picture 12: Do not pull out the seatpost too far

Picture 13: Mount the pedals

Picture 13: Mount the pedals

Hjälpte denna artikel dig?janej