Unfortunately, we do not ship to your country.

Se till vilka länder vi sänder

Kontakta vårt servicenummer. Vi har öppet vardagar till 15:00: 0767 - 650 596

Svårighetsgrad: mellan
I den här kategorin hittar du workshops som lämpar sig åt den riktigt passionerade mekanikern. Du behöver vissa tekniska kunskaper och erfarenhet av underhållsarbete på sportcyklar. För arbeten i den här kategorin kan du komma att behöva speciella verktyg som inte är standard i en vanlig verktygslåda.
Verktyg: Skriv ut artikel

Use of VCLS Post 2.0

Initial steps


1. Remove the bolts on the head of the seat post.
2. Position the saddle on the seat post head. If the saddle rails are not made of carbon, apply a thin film of grease to the clamped area. Always remain within the marked clamping zones indicated on the saddle rails.
3. Mount the saddle with both outer clamps and bolts (M5x50mm). Both outer clamps must point in the same direction and be congruent. The flat sides of the springs must always be parallel to each other. In addition, you can fit the seat clamp at an angle of 180°, thereby increasing the range of adjustment. In this case you fit all the 4 parts of the seat clamp on the other side.
4. Tighten the bolts to 5Nm. Picture 1 If you can’t tighten the bolts because the saddle rails are oval, do not use force. In such cases please contact our Service Center.


Adjusting the saddle position


1. Loosen and remove the adjusting screw which connects the two flat springs. Picture 2
2. Apply carbon assembly paste to the insides of the flat springs. Picture 3
3. Tighten the screw which connects the two flat springs loosely by hand. DANGER! This is only for adjusting the seat post! Do never ride or sit on the bicycle while any screws are not tightened with the correct torque!
4. Clean the inside of the seat tube. Picture 4 The seat tube must be free from grease and dirt when the seat post is fitted. Also check that the seat tube is free of grooves and sharp edges.
5. Apply carbon assembly paste to the outside of the seat post. Picture 5
6. Push the post into the seat tube. Now you can move the flat springs against each other.Picture 6 When you have found the correct saddle position, pull out the seat post.
7. Tighten the adjusting screw which connects the two flat springs with 7NM. Make sure to place the washer underneath the head of the screw!

Mounting of seat post


1. Insert the seat post into the top tube. Ensure that you adhere to the maximum and minimum insertion length for the seat post. The seat post must be inserted at least as far into the seat tube so that the bottom edge of the seat post is positioned below the bottom of the top tube.
2. Tighten the seat post clamp to a maximum torque of 7 Nm. Picture 7 You should not be able to turn the saddle. Wipe off any excess carbon paste. Picture 8

Always remain within the adjustment range indicated on the seat post. Pay particular attention to the minimum and maximum insertion limits. The bottom edge of the seat post must be inserted at least as far down as the bottom edge of the top tube.

Never apply grease to carbon parts. Always mind the correct torque values.


Canyon jobbar hårt för att informationen här i teknisk support ska vara så korrekt och uppdaterad som möjligt. Dock sker alla reparationer som du gör själv på egen risk. Skulle du vara tveksam över något så ska du skicka in cykeln till oss eller en kvalificerad mekaniker/cykelverkstad. Canyon tar inget ansvar och ger ingen garanti på att informationen här i teknisk support är korrekt.


Picture i: Tighten screws with the correct torque

Picture i: Tighten screws with the correct torque

Picture 2: Losen the tightening scew

Picture 2: Losen the tightening scew

Picture 3: Apply carbon assembly paste

Picture 3: Apply carbon assembly paste

Picture 4: Clean the seat tube

Picture 4: Clean the seat tube

Picture 5: Apply carbon assembly paste to the outside

Picture 5: Apply carbon assembly paste to the outside

Picture 6: Move the two halfs against each other

Picture 6: Move the two halfs against each other

Picture 7:Tighten the adjusting scew

Picture 7:Tighten the adjusting scew

Picture 8: Tighten the seat post clamp

Picture 8: Tighten the seat post clamp

Picture 9: Wipe off any excess carbon paste

Picture 9: Wipe off any excess carbon paste

Hjälpte denna artikel dig?janej