Unfortunately, we do not ship to your country.

Se till vilka länder vi sänder

Vårt servicenter öppnar idag kl 09:00. Du kan nå oss på 0767 - 650 596 eller skicka oss epost.

Svårighetsgrad: mellan
I den här kategorin hittar du workshops som lämpar sig åt den riktigt passionerade mekanikern. Du behöver vissa tekniska kunskaper och erfarenhet av underhållsarbete på sportcyklar. För arbeten i den här kategorin kan du komma att behöva speciella verktyg som inte är standard i en vanlig verktygslåda.
Verktyg: Liknande ämnen: Skriv ut artikel

Renthal Stems Installation Instructions

Renthal Duo installation instructions

Preparations


The fork shaft must be clean, dry and free of burr before starting the installation work.

Install the stem

1. Remove the Ahead cover and the spacer from the fork shaft using the 5 mm Allen key. Picture 1 Picture 2 Picture 3

Important:
Do not undo the screw connection of the bottom half of the stem which is already installed. Otherwise you will have to reset the steering head bearing play. The stem and the steering head bearing has already been set correctly by us.

2. Apply a little grease to the thread and under the screw heads.
3. Position the handlebar in the stem. Align the handlebar so that it is precisely in the centre. Picture 4
4. Place the top half of the stem on the fork shaft and handlebar. Picture 5
5. Now check that the handlebar is correctly positioned and aligned in the stem.
6. Place the two screws from below into the stem and tighten them alternately and crossways to a torque of 5 Nm. Picture 6
7. Place the two screws from above into the stem and tighten them alternately and crossways to a torque of 5 Nm. Picture 7
8. Ensure that the clamping is uniform.
9. Secure the top half to the fork shaft using the silver screw using a torque of 5 Nm. Picture 8
10. Place the spacer on the stem and fork shaft. Picture 9
11. Tightening the securing screw on the Ahead cover with a torque of 4 Nm. Picture 10

Care/Maintenance

  • Check that all the bolts are tightened with the correct torque before every ride.
  • Check all the parts at regular intervals for signs of damage, particularly after accidents and falls.
  • Clean all the screws and parts after fitted or removing the stem or handlebar and regrease the screws.


Renthal Integra installation instructions

Prepare the fork crowns

1. Clean the thread and the adjusting surfaces at the top of the fork bridge.

Install the stem

2. Apply a little grease to the thread and under the screw heads.
Position the handlebar in the stem. Align the handlebar so that it is precisely in the centre.
3. Insert the 6x25 mm screws into the rear installation holes either through the 45 mm or the 50 mm installation boreholes.
4. Insert the M6x35 mm screws into the corresponding front installation boreholes
5. Insert the screws into the fork crown mounting at the front.
6. Tighten the screws on the fork crown by hand initially.
7. Tighten the screws on the fork crown alternately crossways with a torque of 10 Nm.
8. Insert the M5x16mm screws into the handlebar mounting and align the handlebar.
9. Tighten the screws on the handlebar mounting alternately and crossway with a torque of 6 Nm.

Care/Maintenance

  • Check that all the bolts are tightened with the correct torque before every ride.
  • Check all the parts at regular intervals for signs of damage, particularly after accidents and falls.
  • Clean all the screws and parts after fitted or removing the stem or handlebar and regrease the screws.

Canyon jobbar hårt för att informationen här i teknisk support ska vara så korrekt och uppdaterad som möjligt. Dock sker alla reparationer som du gör själv på egen risk. Skulle du vara tveksam över något så ska du skicka in cykeln till oss eller en kvalificerad mekaniker/cykelverkstad. Canyon tar inget ansvar och ger ingen garanti på att informationen här i teknisk support är korrekt.


Picture 1:Undo the screw on top of the ahead stem cap

Picture 1:Undo the screw on top of the ahead stem cap

Picture 2:Remove the cap

Picture 2:Remove the cap

Picture 3: Remove the Spacer

Picture 3: Remove the Spacer

Picture 4: Fit the handlebar

Picture 4: Fit the handlebar

Picture 5: Place the top half of the stem on the fork shaft and handlebar

Picture 5: Place the top half of the stem on the fork shaft and handlebar

Picture 7: Tighten the two screws at the bottom with the correct torque

Picture 7: Tighten the two screws at the bottom with the correct torque

Picture 6: Tighten the front screws with the correct torque

Picture 6: Tighten the front screws with the correct torque

Picture 8: Tighten the screw at the back withthe correct torque

Picture 8: Tighten the screw at the back withthe correct torque

Picture 9: Mount the spacer

Picture 9: Mount the spacer

Picture 10:Tighten the scew of the ahead cap with the correct torque

Picture 10:Tighten the scew of the ahead cap with the correct torque

Hjälpte denna artikel dig?janej