Bohužel, nezasíláme do této destinace.

SERVICE CHAT TALK TO THE PEOPLE THAT BUILD YOUR BIKE:

CHAT IS NOT AVAILABLE RIGHT NOW. WE WILL BE BACK ONLINE SOON.

Naše servisní místo bude dostupné opět zítra od 8:30. Zašlete nám prosím e-mail.
Obtížnost: lehké
Tyto úkony zvládne každý kdo se zajímá o cyklistiku. K těmto opravám nepotřebujete buď vůbec žádné nářadí nebo si vystačíte s tím standardním jako jsou imbusové klíče, kleště nebo šroubovák. V této kategorii najdete především jak provést na kole nastavení.
Nástroje: Podobná témata: Vytisknout článek

Adjusting of compression and platform

The compression regulates how fast the shock compresses. If, for example, you are experiencing unwanted suspension bob on your bike, you can counteract this by adjusting the hardness of the compression. This also helps when the suspension fork compresses too far when riding down steps or bottoms out with hard shocks.

The adjusting screws for compression are often blue and located near the screws for adjusting the rebound. However, please note that the not all shocks allow the rider to adjust the compression.

The lower the compression, the more sensitive and comfortable the suspension performance will be.

Lockout

The Lockout function allows the rider to effectively switch off the shock’s compression. RockShox suspension forks allow you to activate the lockout via the PopLoc lever on the handlebar. Picture 1 Magura forks also have the Lockout lever on the handlebar. DT Swiss forks can be blocked by turning the silver knob on the top right of the fork crown.

FOX RL and RLC forks allow you to intensify the level of compression right through to total Lockout via the blue lever. Picture 2 The fork then only compresses when the bike hits extremely hard bumps. On FOX forks with RLC technology the breakaway torque can be adjusted. The breakaway torque can be adjusted via the black knob on the top right of the fork crown. If you turn the knob clockwise, you increase the trigger force that is required to make the fork compress. Picture 3


High Speed und Low Speed Compression

With some RockShox and FOX models you can adjust the high speed and low speed compression separately, i.e. the speed dependent damping.

High speed compression absorbs shocks which only affect the fork very momentarily, for example roots, stones or steps. The higher the high speed compression is, the greater is the protection against bottom-out. The low speed compression, however, counteracts loads which affect the suspension for longer periods, for example when riding through banked bends, during shifts of weight or when braking. The low speed compression prevents the fork from sinking further down which would result in a reduction of travel.

You can set up high- and lowspeed rebound and compression on the Cane Creek Double Barrel damper. You can adjust the compression with the screws on the left hand side and the rebound with the screws on the right hand side.

You can adjust the lowspeed performance with the small screws and the highspeed performance with the bigger screws.

With the Totem fork you can adjust the high speed compression via the blue adjusting wheel at the top right of the fork crown. The low speed compression is adjusted via the smaller silver adjusting wheel. Picture 4

With FOX RC2 models you can adjust the high speed compression on the upper blue adjusting wheel at the bottom of the right-hand fork stanchion. Picture 5 Picture 6 The low speed compression regulator is somewhat smaller and is positioned directly below it. Picture 7 On RLC models the blue low speed adjusting knob is at the top right of the fork crown. Picture 8

Adjustment of the Terralogic threshold


The Terralogic threshold adjuster is a blue knob fitted to the relevant FOX forks at the bottom of the left-hand stanchion.

Plattform and Floodgate

Older RockShox Totem and SID forks are fitted with the Floodgate system. If the Floodgate is activated negative influences created by the drive-train such as bob are suppressed. Shocks from the trail are, however, absorbed. FOX RLC forks and the RockShox Monarch 4.2 shock are fitted with a platform. This overrides the Lockout function when the severity of shocks reaches a certain level and the fork compresses.

With platform systems trigger force can be adjusted. The trigger force is the force which is required to override the lockout and to make the fork compress.

The above mentioned FOX forks allow you to adjust the trigger force using the black wheel on the fork crown.

With Totem forks you need to press on the silver button, which is on the top right of the fork crown. The button then jumps out and must be turned 90° anticlockwise. In the middle of the screw the intensity of the Floodgate can be adjusted using a 2.5mm Allen key or you simply turn the screw by hand. When the Floodgate is activated, ensure that there is sufficient clearance between the down tube and the adjuster knob. With the Monarch 4.2 shock you can switch the Floodgate on and off via the blue lever. Picture 10 By using the golden buttton you can adjust the intensity of the Floodgate. Picture 11


The strength of the platform depends on the ground and the weight of the rider. The heavier the rider and the more uneven the ground is, the stronger the platform strength adjustment should be.

We recommend the following Floodgate adjustment for RockShox forks with the above mentioned adjustment ranges:

Turn the Floodgate adjuster wheel out and then clockwise right to the end. Then turn it anticlockwise as indicated in the table below:

< 63 kg: 4 – 5 Revolutions
63-72 kg: 3 – 4 Revolutions
72-81 kg: 2 – 3 Revolutions
81-90kg: 1 – 2 Revolutions
99 kg<: 0 – 1 Revolutions


Canyon důsledně kontroluje kvalitu informací uvedených v tomto Centru technické podpory. Jakékoliv opravy nebo úpravy na kole jsou na vaši zodpovědnost. Nevíte-li jak něco opravit zašlete kolo do Canyonu nebo jej svěřte odbornému servisu. Canyon neposkytuje záruku a ani nepřebírá žádnou zodpovědnost za informace obsažené v tomto Centru technické podpory.


Picture 1: Rock Shox Pop Lock knob

Picture 1: Rock Shox Pop Lock knob

Picture 2: Locking a Fox 32 Float fork

Picture 2: Locking a Fox 32 Float fork

Picture 3: Adjusting of threshold of Fox 32 Float forks

Picture 3: Adjusting of threshold of Fox 32 Float forks

Picture 4: Adjusting of high and low speed compression on Rock Shox Totem forks

Picture 4: Adjusting of high and low speed compression on Rock Shox Totem forks

Picture 5: The compression knob is placed inside the black cap

Picture 5: The compression knob is placed inside the black cap

Picture 6: Adjusting of highspeed compression on RC2 forks

Picture 6: Adjusting of highspeed compression on RC2 forks

Picture 7: Adjusting of lowspeed compression of Fox RC2 forks

Picture 7: Adjusting of lowspeed compression of Fox RC2 forks

Picture 8: Adjusting of highspeed compression on Fox RLC forks

Picture 8: Adjusting of highspeed compression on Fox RLC forks

Picture 9: You can adjust the floodgate using the silver knob

Picture 9: You can adjust the floodgate using the silver knob

Pomohl vám tento článek?anone

Pure Cycling.