Unfortunately, we do not ship to your country.

SERVICE CHAT TALK TO THE PEOPLE THAT BUILD YOUR BIKE:

CHAT IS NOT AVAILABLE RIGHT NOW. WE WILL BE BACK ONLINE SOON.

Vi er tilgjengelige igjen mandag 09:00. Send oss en e-mail.
Vanskelig : Lett
Disse oppgavene er enkle for alle som er interessert i sykling. I denne "workshoppen" trenger brukeren enten ingen verktøy, eller han foretrekker standard verktøy som f.eks. Allen nøkler, tenger eller skrutrekkere. I denne kategorien vil du framfor alt finne ut hvordan du kan utføre justeringer på din sykkel.
Verktøy : Lignende temaer : Trykket artikkel

Adjusting of ProPedal and BoostValve

ProPedal damping affects the initial part of the compression stroke and is designed to control annoying pedal-induced suspension bob. ProPedal doesn’t block the shock entirely and the entire range of travel is always available to the rider.

This is how you adjust ProPedal :

Using the blue lever you can switch the ProPedal system on and off. Picture 1 Picture 2

Using the blue adjusting knob you can adjust the intensity of the ProPedal function. Picture 3 Pull out the knob and turn it in the desired direction while the ProPedal function is switched on. Only turn the knob when the bike is stationary and not while riding.

There are 3 levels of adjustment on ProPedal. The level of intensity you select depends on the ground you are riding on and your weight. The heavier the rider and the rougher the terrain, the higher the level of intensity ProPedal should be.

On easy and medium tough terrain you can use the following guide lines:

Rider weight <85kg: Low ProPedal intensity
Rider weight 85-95kg: Medium ProPedal intensity
Rider weight >95kg: High ProPedal intensity
Der RP2 does not have these adjustment options.

Boost Valve adjustment

On Fox RP2, RP23, DHX 4.0 and DHX Air 5.0 shocks there is a Boost Valve function. This dynamic form of damping depends on how far the shock is compressed. The further the shock compresses, the greater is the effect of the rebound in absorbing shocks. Slighter shocks are absorbed with less pressure, harder shocks with greater pressure. This function is also active when the ProPedal function is switched on and acts as bottom out protection for your shock.

The Boost Valve function is regulated via the air pressure of the shock or Piggy-Back. A firmer ride is achieved with higher pressure and a softer ride with lower pressure. In the case of the DHX 4.0 and DHX 5.0 you can, with the help of a shock pump, adjust the air pressure in the Boost Valve. At the rear on the Piggy-Back there is a valve. There you can regulate the air pressure in the Boost Valve using a shock or fork pump.


Highest and lowest air pressure in the BoostValve-chamber

DHX 4.0: 8.62-15.51 Bar
DHX Air 5.0: 8.62-15.51 Bar

The Boost Valve on the RP23 and RP2 can only be changed by the FOX service center.

The air pressure should be high enough to prevent the damper from bottoming out but not exceed the maximum air pressure.


Canyon forsøker hele tiden å sikre kvaliteten og nøyaktigheten i den informasjonen som legges ut her i Teknisk Support Senter. Likevel er alle reparasjoner og justeringer som du utfører på egen risiko. Er du i tvil med hensyn til hvordan du skal gjøre det, anbefaler vi deg å sende sykkelen til Canyon eller levere den til et kvalifisert sykkelverksted. Canyon gir ingen garantier og tar ikke ansvar for den informasjon som legges ut her i Teknisk Support Senter.

Picture 1: ProPedal on the Fox RP 23 damper

Picture 1: ProPedal on the Fox RP 23 damper

Picture 2: Switching off ProPedal function on the Fox DHX 5.0 Air damper

Picture 2: Switching off ProPedal function on the Fox DHX 5.0 Air damper

Picture 3: Setting the strength nf the ProPedal of the Fox RP 23 damper

Picture 3: Setting the strength nf the ProPedal of the Fox RP 23 damper

Hjalp den artikkelen deg?JaNei

Pure Cycling.